ENE KB930QF A1
KB3920 extends the channels of Interrupt Controller in the original 8051 to 24 channels supporting internal peripheral devices. The Serial port use SCON2 to achieve high speed serial transmission rate up to 115200 bps. The two 16-bit timers are basically the same as that in the standard 8051’s, except when SCON2 is used to generate high-speed baud rate. Under such circumstances the 2 timers will not be used for baud-rate generation but for other purposes. The 8051 uses MOVX and MOVC instructions to read or write...
SKU: ZZ10.CIC113
RT8870A
The RT8870A is a dual-output PWM controller for AMD SVI mobile CPU power supply. The RT8870A provides a two-phase PWM controller to power the CPU Core (VDD) and a single-phase PWM controller to power the Northbridge portion of the CPU (VDDNB). This part has three integrated MOSFET drivers and is fully compliant with AMD Voltage Regulator Specification to meet AMD’s mobile CPU power supply requirements. The RT8870A features CCRCOT (Constant Current Ripple Constant On-Time) control with G-NAVPTM (Green-Native AVP),...
SKU: ZZ10.CIC112
ISL 95831 HRTZ
ISL95831, 95831HRZ, 95381Compliant with IMVP-7/VR12™, the ISL95831 provides a complete solution for microprocessor and graphic processor core power supply. It provides two Voltage Regulators (VRs) with three integrated gate drivers. The first VR can be configured as 3-, 2- or 1-phase VR while the second output is 1- phase VR, providing maximum flexibility. The two VRs share the serial control bus to communicate with the CPU and achieve lower cost and smaller board area compared with the two-chip approach. Based...
SKU: ZZ10.CIC109
LT3850
LT3850 LT 3850 LT 8F LT8FThe LTC®3850 is a high performance dual synchronous step-down switching regulator controller that drives all N-channel power MOSFET stages. A constant-frequency current mode architecture allows a phase-lockable frequency of up to 780kHz. Power loss and supply noise are minimized by operating the two controller output stages out of phase. OPTI-LOOP® compensation allows the transient response to be optimized over a wide range of output capacitance and ESR values. The LTC3850 features a...
SKU: ZZ10.CIC108
MAXIM 17480G
The MAX17480 is a triple-output, step-down, fixedfrequency controller for AMD’s serial VID interface (SVI) CPU and northbridge (NB) core supplies. The MAX17480 consists of two high-current SMPSs for the CPU cores and one 4A internal switch SMPS for the NB core. The two CPU core SMPSs run 180° out-of-phase for true interleaved operation, minimizing input capacitance. The 4A internal switch SMPS runs at twice the switching frequency of the core SMPS, reducing the size of the external components. The MAX17480 is...
SKU: ZZ10.CIC107
MAXIM MAX1632AEAI
The MAX1630A–MAX1635A are buck-topology, stepdown, switch-mode, power-supply controllers that generate logic-supply voltages in battery-powered systems. These high-performance, dual-/triple-output devices include on-board power-up sequencing, power-good signaling with delay, digital soft-start, secondary winding control, low-dropout circuitry, internal frequency-compensation networks, and automatic bootstrapping. Up to 96% efficiency is achieved through synchronous rectification and Maxim’s proprietary Idle...
SKU: ZZ10.CIC106
MAXIM MAX1532A
The MAX1532 is a dual-phase, Quick-PWM™, step-down controllers for Intel IMVP™ CPU core supplies. Dual-phase operation reduces input ripple current requirements and output voltage ripple while easing component selection and layout difficulties. The Quick-PWM control scheme provides instantaneous response to fast load-current steps. The MAX1546 includes active voltage positioning with adjustable gain and offset, reducing power dissipation and bulk output capacitance requirements. The MAX1532 is intended for two...
SKU: ZZ10.CIC105
MAXIM 8632E
The MAX8632 integrates a synchronous-buck PWM controller to generate VDDQ, a sourcing and sinking LDO linear regulator to generate VTT, and a 10mA reference output buffer to generate VTTR. The buck controller drives two external n-channel MOSFETs to generate output voltages down to 0.7V from a 2V to 28V input with output currents up to 15A. The LDO can sink or source up to 1.5A continuous and 3A peak current. Both the LDO output and the 10mA reference buffer output can be made to track the REFIN voltage. These...
SKU: ZZ10.CIC103
S29AL008D70TFI01
The S29AL008D70TFI01 is an 8 Mbit, 3.0 volt-only Flash memory organized as 1,048,576 bytes or 524,288 words. The device is offered in 48-ball FBGA, 44-pin SO, and 48-pin TSOP packages. For more information, refer to publication number 21536. The word-wide data (x16) appears on DQ15–DQ0; the byte-wide (x8) data appears on DQ7–DQ0. This device requires only a single, 3.0 volt VCC supply to perform read, program, and erase operations. A standard EPROM programmer can also be used to program and erase the device....
SKU: ZZ10.CIC102
SMSC KB1070-NU
Standard MicroSystems Corp KBC1070-NU Keyboard Controller for Compal
SKU: ZZ10.CIC101
RT8152D
General Description The RT8152C/D is a single phase PWM controller with integrated MOSFET drivers. Moreover, it is compliant with Intel IMVP6.5 Voltage Regulator Specification to fulfill its mobile CPU core and Render core voltage regulator requirements. The RT8152C/D adopts G-NAVP (GreenNative AVP), which is a Richtek's proprietary topology derived from finite DC gain compensator constant on-time mode, making it an easy setting PWM controller meeting all Intel AVP (Active Voltage Positioning) mobile CPU/ Render...
SKU: ZZ10.CIC099
ROHM BD2224G
General Description BD2224G and BD2225G are low ON-Resistance N-Channel MOSFET high-side power switches, optimized for Universal Serial Bus (USB) applications. BD2224G and BD2225G are equipped with the function of over-current detection, thermal shutdown, under-voltage lockout and soft-start.
SKU: ZZ10.CIC098
MAXIM 8725E
The MAX8725 evaluation kit (EV kit) is an accurate and efficient multichemistry battery charger. The EV kit can charge three or four series Li+ cells with a current up to 3A. Charge current and input-source current are adjustable using on-board potentiometers. The output voltage is set to 4.2V ✕ the number of series cells in the battery pack. The number of series cells is jumper selectable. The output voltage is adjustable between 4V to 4.4V (✕ the number of series cells) by installing two resistors. The EV kit...
SKU: ZZ10.CIC093
MAXIM 17005B
The MAX17005/MAX17006/MAX17015 are high-frequency multichemistry battery chargers. These circuits feature a new high-frequency current-mode architecture that significantly reduces component size and cost. The charger uses a high-side MOSFET with n-channel synchronous rectifier. Widely adjustable charge current, charge voltage, and input current limit simplify the construction of highly accurate and efficient chargers. The charge voltage and charge current are set with analog control inputs. The charge current...
SKU: ZZ10.CIC087
MAXIM MAX8742E
The MAX8741/MAX8742 are buck-topology, step-down, switch-mode, power-supply controllers that generate logic-supply voltages in battery-powered systems. These high-performance, dual/triple-output devices include onboard power-up sequencing, power-good signaling with delay, digital soft-start, secondary winding control, lowdropout circuitry, internal frequency-compensation networks, and automatic bootstrapping. Up to 97% efficiency is achieved through synchronous rectification and Maxim’s proprietary Idle Mode™...
SKU: ZZ10.CIC085
MAX8724
The MAX1908/MAX8724/MAX8765/MAX8765A highly integrated, multichemistry battery-charger control ICs simplify the construction of accurate and efficient chargers. These devices use analog inputs to control charge current and voltage, and can be programmed by the host or hardwired. The MAX1908/MAX8724/MAX8765/ MAX8765A achieve high efficiency using a buck topology with synchronous rectification.
SKU: ZZ10.CIC084
MAX8771
The MAX8770/MAX8771/MAX8772 are 2/1-phase interleaved Quick-PWM™ step-down VID power-supply controllers for notebook CPUs. True out-of-phase operation reduces input ripple current requirements and output voltage ripple while easing component selection and layout difficulties. The Quick-PWM control provides instantaneous response to fast load current steps. Active voltage positioning reduces power dissipation and bulk output capacitance requirements and allows ideal positioning compensation for tantalum, polymer,...
SKU: ZZ10.CIC083
RT9018B /A
The RT9018A/B is a high performance positive voltage regulator designed for use in applications requiring very low Input voltage and very low dropout voltage at up to 3A(Peak). It operates with a VIN as low as 1.4V and VDD voltage 3V with output voltage programmable as low as 0.8V. The significant feature includes ultra low dropout, ideal for applications where VOUT is very close to VIN. Additionally, there is an enable pin to further reduce power dissipation while shutdown. The RT9018A/B provides excellent...
SKU: ZZ10.CIC079
ISL 6261
The ISL6261 is a single-phase buck regulator implementing lntel® IMVP-6® protocol, with embedded gate drivers. The heart of the ISL6261 is the patented R3 Technology™, Intersil’s Robust Ripple Regulator modulator. Compared with the traditional multi-phase buck regulator, the R3 Technology™ has faster transient response. This is due to the R3 modulator commanding variable switching frequency during a load transient.
SKU: ZZ10.CIC078
MAX17080C
The MAX17080 is a triple-output, step-down, fixed frequency controller for AMD’s serial VID interface (SVI) CPU and northbridge (NB) core supplies. The MAX17080 consists of two high-current SMPSs for the CPU cores and one 3A internal switch SMPS for the NB core. The two CPU core SMPSs run 180° out-of-phase for true interleaved operation, minimizing input capacitance. The 3A internal switch SMPS runs at twice the switching frequency of the core SMPS, reducing the size of the external components.
SKU: ZZ10.CIC076